Cisco CCNP Certification / BCMSN Exam Tutorial: The HSRP MAC Address Article Cisco CCNP Certification / BCMSN Exam Tutorial: The HSRP MAC Address Article
    home | all categories | submit articles | about us | links | link to us | site map | contact us | recommended resources
 
Home » Articles » Computers » networks » Cisco CCNP Certification / BCMSN Exam Tutorial: The HSRP MAC Address

Cisco CCNP Certification / BCMSN Exam Tutorial: The HSRP MAC Address


By Chris Bryant

Cisco CCNP Certification / BCMSN Exam Tutorial: The HSRP MAC Address

To pass the BCMSN exam and earn your CCNP, you've got to know HSRP inside and out! Part of that is knowing how the MAC address of the virtual router is derived, and another part is knowing how to change this address. We'll look at both features in this tutorial.

We've got two routers on a segment running HSRP, so first we need to find out what the MAC address of the HSRP virtual router is. The show command for HSRP is show standby, and it's the first command you should run while configuring and troubleshooting HSRP. Let's run it on both routers and compare results.

R2#show standby

Ethernet0 - Group 5

Local state is Standby, priority 100

Hellotime 3 sec, holdtime 10 sec

Next hello sent in 0.776

Virtual IP address is 172.12.23.10 configured

Active router is 172.12.23.3, priority 100 expires in 9.568

Standby router is local

1 state changes, last state change 00:00:22

R3#show standby

Ethernet0 - Group 5

Local state is Active, priority 100

Hellotime 3 sec, holdtime 10 sec

Next hello sent in 2.592

Virtual IP address is 172.12.23.10 configured

Active router is local

Standby router is 172.12.23.2 expires in 8.020

Virtual mac address is 0000.0c07.ac05

2 state changes, last state change 00:02:08

R3 is in Active state, while R2 is in Standby. The hosts are using the 172.12.123.10 address as their gateway, but R3 is actually handling the workload. R2 will take over if R3 becomes unavailable.

An IP address was statically assigned to the virtual router, but not a MAC address. However, there is a MAC address under the show standby output on R3, the active router. How did the HSRP process arrive at a MAC of 00-00-0c-07-ac-05?

Well, most of the work is already done before the configuration is even begun. The MAC address 00-00-0c-07-ac-xx is reserved for HSRP, and xx is the group number in hexadecimal. That's a good skill to have for the exam, so make sure you're comfortable with hex conversions. The group number is 5, which is expressed as 05 with a two-bit hex character. If the group number had been 17, we'd see 11 at the end of the MAC address - one unit of 16, one unit of 1.

On rare occasions, you may have to change the MAC address assigned to the virtual router. This is done with the standby mac-address command. Just make sure you're not duplicating a MAC address that's already on your network!

R2(config-if)#standby 5 mac-address 0000.1111.2222


1d12h: %STANDBY-6-STATECHANGE: Ethernet0 Group 5 state Active -> Learn


R2#show standby

Ethernet0 - Group 5

Local state is Active, priority 150, may preempt

Hellotime 4 sec, holdtime 12 sec

Next hello sent in 3.476

Virtual IP address is 172.12.23.10 configured

Active router is local

Standby router is 172.12.23.3 expires in 10.204

Virtual mac address is 0000.1111.2222 configured

4 state changes, last state change 00:00:00


1d12h: %STANDBY-6-STATECHANGE: Ethernet0 Group 5 state Listen -> Active

The MAC address will take a few seconds to change, and the HSRP routers will go into Learn state for that time period.

A real-world HSRP troubleshooting note: If you see constant state changes with your HSRP configuration, do what you should always do when troubleshooting - check the physical layer first. Best of luck on your BCMSN exam!



About the author

Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage , home of free CCNA and CCNP tutorials! Pass the CCNA exam with Chris Bryant! from http://www.FreeArticlesAndContent.com

Copy This Article For FREE!!!

You can use this article and copy it on your own website for free! All you have to do is make sure the article is copied with no changes and includes the "About The Author" text. Also please ensure that all url's are hyperlinked according. Thank you.

Link To This Article - And We'll Link Back To Your Website!

You are more then welcome to link to this article! All you have to do is copy this webpage address from the address bar and create a link on your website. Please use the title of this article for your link text. Please get in contact once you have linked to this article and we'll link back to you! Thank you.
 
Other great articles from this category...


The Importance Of RJ45 Cables For Networking
Wednesday, 24th September 2008

How Helpful A Web Proxy Can Be?
Wednesday, 10th September 2008

Discovering Your Local Area Network
Friday, 5th September 2008

Use a Proxy Site for Anonymous Browsing
Wednesday, 20th August 2008

Moving To An NGN Platform
Friday, 1st August 2008

What can WiMAX technology offer?
Tuesday, 15th July 2008


Related Sites





Free Articles

Unsecured Credit Card Application   Free Proxy   Motorola MotoPEBL   Dog Training
Copyright © 2005-2008 Your Marketing Ltd. All Rights Reserved