Cisco CCNP / BSCI Exam Tutorial: Configuring And Troubleshooting OSPF Virtual Links
By Chris Bryant
Knowing when and how to create an OSPF virtual link is an essential skill for BSCI and CCNP exam success, not to mention how important it can be on your job! As a CCNA and CCNP candidate, you know the theory of virtual links, so let's take a look at how to configure a virtual link, as well as some real-world tips that many CCNA and CCNP study guides leave out!
In this configuration, no router with an interface in Area 4 has a physical interface in Area 0. This means a logical connection to Area 0, a virtual link, must be built.
In the following example, R1 and R3 are adjacent and both have interfaces in Area 0. R4 has an adjacency with R3 via Area 34, but R4 has no physical interface in Area 0 and is advertising its loopback 4.4.4.4 into OSPF. R1 doesn't have the route to that loopback.
R1#show ip route ospf
6.0.0.0/32 is subnetted, 1 subnets
O 6.6.6.6 [110/11] via 10.1.1.5, 01:05:45, Ethernet0
172.23.0.0/27 is subnetted, 1 subnets
O IA 172.23.23.0 [110/74] via 172.12.123.3, 00:04:14, Serial0
7.0.0.0/32 is subnetted, 1 subnets
O 7.7.7.7 [110/11] via 10.1.1.5, 01:05:45, Ethernet0
To resolve this, a virtual link will be built between R3 and R4 through Area 34. The area through which the virtual link is built, the transit area, cannot be a stub area of any kind.
R4(config)#router ospf 1
R4(config-router)#area 34 virtual-link 3.3.3.3
R3(config)#router ospf 1
2d07h: %OSPF-4-ERRRCV: Received invalid packet: mismatch area ID, from backbone area must be virtual-link but not found from 172.23.23.4, Ethernet0
R3(config)#router ospf 1
R3(config-router)#area 34 virtual-link 4.4.4.4
R3(config-router)#^Z
2d07h: %OSPF-5-ADJCHG: Process 1, Nbr 4.4.4.4 on OSPF_VL0 from LOADING to FULL, Loading Done
A few details worth noting... the virtual link command uses the remote device's RID, not necessarily the IP address on the interface that's in the transit area. Also, don't worry about that error message you see in the output from R3 that is normal and you'll see it until you finish building the virtual link.
Always confirm the virtual link with show ip ospf virtual-link. If you've configured it correctly, the VL should come up in a matter of seconds.
R3#show ip ospf virtual-link
Virtual Link OSPF_VL0 to router 4.4.4.4 is up
Run as demand circuit
DoNotAge LSA allowed.
Transit area 34, via interface Ethernet0, Cost of using 10
Transmit Delay is 1 sec, State POINT_TO_POINT,
Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
Hello due in 00:00:00
Adjacency State FULL (Hello suppressed)
Index 2/4, retransmission queue length 1, number of retransmission 1
First 0x2C8F8E(15)/0x0(0) Next 0x2C8F8E(15)/0x0(0)
Last retransmission scan length is 1, maximum is 1
Last retransmission scan time is 0 msec, maximum is 0 msec
Link State retransmission due in 3044 msec
Virtual links are actually simple to configure, but for some reason they seem to intimidate people. It's my experience that the error message highlighted in R3's output above causes a lot of panic, but the only thing that message means is that you're not finished configuring the virtual link yet.
There are three main misconfigurations that cause 99% of virtual link configuration issues:
Using the wrong OSPF RID value
Trying to use a stub area as the transit area
Failure to configure link authentication on the virtual link when Area 0 is running authentication
That last one is the one that gets forgotten! A virtual link is really an extension of Area 0, and if Area 0 is running link authentication, the virtual link must be configured for it as well. Pay attention to the details. don't panic when you see the error message on the second router you configure with the virtual link, and you'll be ready for any virtual link situation on the job or in the CCNA / CCNP exam room!
About the author
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage , home of free CCNA and CCNP tutorials! Pass the CCNA exam with Chris Bryant! from http://www.FreeArticlesAndContent.com
|
|
Copy This Article
For FREE!!!
You can use this article and copy it on your own website
for free! All you have to do is make sure the article
is copied with no changes and includes the "About
The Author" text. Also please ensure that all url's
are hyperlinked according. Thank you. |
Link To This Article - And We'll
Link Back To Your Website!
You are more then welcome to link to this article! All
you have to do is copy this webpage address from the
address bar and create a link on your website. Please
use the title of this article for your link text. Please
get in contact once you have linked to this article
and we'll link back to you! Thank you. |
|
|
|
Other great articles from this category...
|
Related Sites
|
|
